Everyone who has ever faced a drip drop for hours can tell you that a leaky faucet is not a fun thing to have. Steady drops – drop, drop, drop can easily make anyone go mad, let alone, waste water and hike your utilities bills. But don’t worry! As scary as it sounds there is nothing as easy as fixing a leaky single handle bathroom faucet by Plumber Sharjah. In fact, this problem can be solved by you yourself with just a few procedures.
Here is some problems and solutions
Understanding Your Faucet
First of all, it’s good that we learn the names of the elements of your faucet. A typical single handle bathroom faucet has a few key components: handle, cartridge, or seal respectively. The primary function of the seal is to avoid leakage and the one of the cartridge is to regulate the water supply. If either is worn out then this is where you will likely be finding your leak.
Gathering Your Tools
You’ll need some basic tools to get started. Here’s a quick list:
- Screwdriver (Phillips or flathead)
- Adjustable wrench
- Plumber’s grease
- Replacement parts (cartridge or seals)
Having these tools ready will make the job easier. It’s like having your favorite junk food during the series watch!
Shutting Off the Water Supply
The first step to tap dancing is to shut off the water supply to your faucet. The two main shut-off valves can be found beneath the sink. Twist them to the right in order that they get well tightened. Leaving the water running is as absurd as starting a recipe without checking for the ingredients. Plumber Sharjah solve your all water problems.
Removing the Faucet Handle
Now it’s time to take off the handle. Generally, there is a small screw on the back of the handle or under the knob. Just take it out using your screwdriver You better use your screwdriver to do it. If getting the screw loose becomes difficult then simply pull the handle as high as possible. If it feels resistant, bend it a little while pulling; just don’t snap it.
Inspecting the Cartridge
After turning the handle you should be able to see the cartridge. This is where, mainly, leaks originate from. Observing eye defects: try to identify any form of defect/ wear/ tear that can be seen with naked eye. You will know if it is cracked or worn out, depending on your circumstances. It may need replacement.
Replacing the Cartridge
Use your adjustable wrench to remove the nut that secures the main cartridge. Then, take off the cartridge. When it’s free, you can take it out. Remainder the old one with the new cartridge so that you can get an identically compatible cartridge from the store. It’s like having a picture of their favorite meal at a restaurant. They want to be sure they are getting exactly that.
After you have the new cartridge, apply some plumber Sharjah grease to it. Then, gently slide the cartridge into the slot. Bolt it and lock it using the retaining nut. Do not over-tighten it. You only need to tighten it until it fits slightly.
Reassembling Everything
Place the handle back on and screw the handle on to make it tight once more. Do not also fail to put back any decorative caps, which you removed in the course of the learning. It’s like the cherry on top of the sundae, you want it to be appealing!
Turning the Water Back On
It’s now time to turn on the water after every part has been reassembled as explained above. Walk carefully you do not want any water pressure buildups. After turning it on, turn on the faucet and allow it run for a minute to check for leaks. If there is no drip, then congratulations to you! You are just done repairing a dripping faucet.
Conclusion
Repairing a leaky single-handle bathroom faucet is easier than you think. With a few tools, some time, and these steps, you can save water and money. You’ll also feel a sense of accomplishment. Now, every time you wash your hands you do not have this drip to remind you of your success. Well then, here are the gloves off, time to get to the work. For more information about Plumbing Services in Dubai, call our toll-free number 045490505.